2018 Enclosed Red Concession Trailer for Sale in Scappoose, Oregon

Type of Mobile Food Unit

Asking Price - $39000.00
Year of Vehicle - 2018
Make of Vehicle - TRAILER
Model of Vehicle - ENCLOSED TRAILER 16
Mileage of Vehicle - 0
Fuel Type - Does Not Apply
Length - 21
Height -
Permits - YES
Cooking Equipment - Burner Stove, Griddle, Broiler
Storage - Fridge, Cabinets
Health & Sanitation - 3 Compartment Sink, Hand Wash Sink, Soap Dispenser
Operations - Propane
Other - TV


First Name - Adam
Last Name - Ortega Vargas
Phone - 5035728454

Email - ortegascoating@msn.com

  • Description
  • Contact
  • Video Files

Selling our like new Food Cart Class 4. Used no more than 4 months. We have decided to move into a Brick and Mortar location. We had our Food Cart custom built right, Heavy Duty. Has tempered glass. Has to much to list so look at the pictures. took over Three months for delivery. So there is no waiting for you.

The trailer is 21 feet with tongue. Any questions give me a call. thanks for looking
Double Axle 16 ft Trailer

*8 ft W x 16 ft L Enclosed Double 5,200 lb Axles Food Trailer
(+4 ft tongue).
*E-rated trailer tires
*Safety chains, electric brakes and breakaway kit per DOT
*18 3/4 Stainless Steel Counters
*Stainless Steel Storage Shelves, 1 ft Deep
*50 AMP Power Inlet
*2, LED 4 ft fixtures with 2 LED tubes in each
*Eaton Cutler-Hammer 125-Amp, 12-Space, two 4-Circuit
Type-BR Outdoor Main Lug Sub Feed Panel
*SHURflo On-Demand Water Pump and Accumulator
*80 Gal. Fresh Water Tank (a 50-gallon freshwater tank will
be installed for trailers in the state of CA).
*98 Gal. Grey Water Tank
*City pressured water, using city water (Bypasses freshwater
tank and water pump, unlimited water as long as you have
the hose plugged in).
*NSF approved 17 in W hand wash sink with 10 in x 14 in x 5
in basin
*Fresh water inlet (garden hose thread)
*Soap Dispenser
*Paper Towel Dispenser
*1 ft x 1 ft Roof Air Vent
*Fiber Reinforced Plastic Ceiling (FRP)
*36 in x 72 in (Rough opening) Main Entrance Door
*Comprehensive Trailer Plan
*Subframe: 3 in I-Beam cross-member on 12 in centers with
4 in long rail. Mylar the tape is applied to all steel subframe
components and extruded aluminum lower bottom rails to
prevent corrosion.
*Floor: 1 1/8 in Laminated hardwood fastened to the
subframe with two countersunk screws per floor board per
cross-member in a staggered pattern. Floorboards are ship-lapped and pre-undercoated for protection from elements.
Hardwood floor is covered with 0.63 aluminum tread plate.
*Skins-Sides: .040 Aluminum, rivets for front and sidewalls.
*Side Wall: Extruded aluminum top and bottom rails with 1
3 /8 in deep galvanized steel Z-shaped vertical posts
installed on 16 in centers.
*Front End: Aerodynamic aluminum radii with steel Z-posts.
.040 aluminum skin.
*Roof: .032 One piece aluminum sheet with anti-snag roof
bows on 24 in centers with crowned roof design which
prevents water/ice pooling. Aerodynamic aluminum radius
and poly-tuff corner caps.
*Exterior Lights: Tecniq S36 LED sealed clearance light, per
Federal Motor Vehicle Safety Standard (FMVSS)-108 installed
in front corner caps, and five across the rear header. LED
turn signals and LED license plate lights.
*Interior Walls: 5/8 Plywood attached to galvanized steel Zshaped
vertical posts with 1 in foam insulation in between
the posts (front and side walls, the back wall is a double
layer of plywood) .24 gauge stainless steel sheets attached
via screws to the plywood walls.
*Interior Ceiling: Fiber reinforced plastic (white) ceiling
attached to the 24 in centers and insulated with 1” foam.
*Welded seam on the floor with 6 in base and 3/8 in radius

Contact Form

No Video Files Attached.


Subscribe to our e-mail newsletter to receive updates.